怎样用Java语言控制双路智能墙壁控制开关

2026-04-20 发布浏览：750 次

本文介绍了如何用 Java 对接智能墙壁复合开关|2路的方法：可以通过接口实现2路独立功能控制、门禁信号联动控制、照明开关联动控制、远程指令开关控制、定时灯光门禁控制、自定义场景联动控制、灯光门禁状态反馈控制、2路独立线路控制、双路照明或门禁控制、远程控制照明与门禁、定时开关照明设备、门禁与照明联动控制、远程打开关闭照明与门禁、设备状态监测与联动、客房场景化控制、物理按键控制照明门禁、远程开关状态查询、场景联动照明门禁控制、设备运行状态监控、远程参数配置管理、故障告警通知、延时通断控制、设备分组控制、多设备联动控制、自定义联动逻辑控制、线路状态反馈控制、本地按键与远程双控制。

智能墙壁复合开关|2路

更多...

适用场景

智能家居照明门禁控制、共享场所灯光门禁管理、智能办公场景门禁照明控制、门店灯光门禁联动控制、共享自习室门禁照明管理、共享茶室门禁灯光控制、无人值守场所门禁照明管理、酒店客房灯光门禁控制、商业空间门禁照明联动控制、办公场所门禁灯光管理、酒店客房智能改造、民宿房间智能控制、共享茶室灯光控制、共享自习室门禁联动、办公室照明门禁控制、店铺照明设备管理、智能公寓客房控制、共享棋牌室设备控制、无人值守空间管理、弱电间设备联动、智能化改造、智能家居照明门禁联动、出租屋照明控制、小型商铺照明管理、共享自习室照明门禁控制、共享台球室灯光控制、共享麻将馆门禁照明联动、无人值守门店照明控制、自助设备照明管理、共享健身房灯光控制、共享充电站照明管理、智慧教室照明控制、培训机构教室灯光管理、图书馆自习室照明控制、创客工坊设备照明管理、学校活动室照明控制、培训教室灯光管理、餐厅包厢照明控制、便利店照明管理、银行网点照明控制、医院病房照明管理、展会现场照明控制、活动现场灯光管理、景观亮化照明控制、广告灯箱照明管理、园区公共照明控制、写字楼办公室照明管理、商场店铺照明控制、社区公共照明管理、设备机房照明控制、实验室照明管理、办公设备照明联动中

支持命令

线路1	power1
线路2	power2
1路状态保持	power1
2路状态保持	power2
1路先通后断	point1
2路先通后断	point2
1路先断后通	reset1
2路先断后通	reset2

产品手册

版本	对应产品手册
左灯右门	《智能墙壁复合开关[左灯右门]产品手册》
左门右灯	《智能墙壁复合开关[左门右灯]产品手册》

HTTP接口控制以设备控制（向设备下发命令）为例

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

/*首先，确保在你的项目中添加了 unirest 的 Maven 依赖。如果你使用的是 Maven，可以在 pom.xml 中添加以下依赖：
<dependency>
    <groupId>com.konghq</groupId>
    <artifactId>unirest-java</artifactId>
    <version>3.13.10</version>
</dependency>
*/

import com.konghq.unirest.http.HttpResponse;
import com.konghq.unirest.http.Unirest;
import com.konghq.unirest.http.exceptions.UnirestException;
import org.apache.commons.codec.digest.DigestUtils;

public class Main {
    public static void main(String[] args) {
        // 定义变量
        String AppID = "开发者ID"; // 替换为实际的 AppID
        String AppSecret = "开发者密码"; // 替换为实际的 AppSecret
        long ts = System.currentTimeMillis() / 1000; // 获取当前时间戳（秒）

        // 计算签名 md5(md5(开发者密码)拼接上面的ts参数)
        String sign = DigestUtils.md5Hex(DigestUtils.md5Hex(AppSecret) + ts);

        // 构建 URL
        String url = String.format("https://api.thingboot.com/%s/device/control/?sign=%s&ts=%d", AppID, sign, ts);

        // 请求体数据
        String device = "1878"; // 替换为实际的设备ID；可传多个[用,间隔]
        String order = "{\"power1\":1}"; // 替换为实际的命令

        try {
            // 构建请求体
            String postData = String.format("{\"device\":\"%s\",\"order\":%s}", device, order);

            // 发送 POST 请求
            HttpResponse<String> response = Unirest.post(url)
                    .header("Content-Type", "application/json")
                    .body(postData)
                    .asString();

            // 输出响应
            System.out.println(response.getBody());
        } catch (UnirestException e) {
            e.printStackTrace();
        }
    }
}

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

/*
首先，确保在你的项目中添加了 OkHttp 的 Maven 依赖。如果你使用的是 Maven，可以在 pom.xml 中添加以下依赖：
<dependency>
    <groupId>com.squareup.okhttp3</groupId>
    <artifactId>okhttp</artifactId>
    <version>4.9.3</version>
</dependency>
*/

import okhttp3.*;
import org.apache.commons.codec.digest.DigestUtils;

import java.io.IOException;

public class Main {
    public static void main(String[] args) {
        // 定义变量
        String AppID = "开发者ID"; // 替换为实际的 AppID
        String AppSecret = "开发者密码"; // 替换为实际的 AppSecret
        long ts = System.currentTimeMillis() / 1000; // 获取当前时间戳（秒）

        // 计算签名 md5(md5(开发者密码)拼接上面的ts参数)
        String sign = DigestUtils.md5Hex(DigestUtils.md5Hex(AppSecret) + ts);

        // 构建 URL
        String url = String.format("https://api.thingboot.com/%s/device/control/?sign=%s&ts=%d", AppID, sign, ts);

        // 请求体数据
        String device = "1878"; // 替换为实际的设备ID；可传多个[用,间隔]
        String order = "{\"power1\":1}"; // 替换为实际的命令

        // 构建请求体
        String postData = String.format("{\"device\":\"%s\",\"order\":%s}", device, order);

        // 创建 OkHttpClient 实例
        OkHttpClient client = new OkHttpClient();

        // 创建请求体
        MediaType mediaType = MediaType.parse("application/json; charset=utf-8");
        RequestBody body = RequestBody.create(postData, mediaType);

        // 创建请求
        Request request = new Request.Builder()
                .url(url)
                .post(body)
                .addHeader("Content-Type", "application/json")
                .build();

        // 发送请求并处理响应
        try (Response response = client.newCall(request).execute()) {
            if (!response.isSuccessful()) throw new IOException("Unexpected code " + response);

            // 输出响应
            System.out.println(response.body().string());
        } catch (IOException e) {
            e.printStackTrace();
        }
    }
}

说明：{AppID}为您的应用ID（由平台生成），免费注册登录后，可在控制台查看；sign和ts的取值，请参考文档。