怎样用PHP语言对接16A带计量智能插座

2026-03-24 发布浏览：983 次

本文介绍了如何用 PHP 对接智能插座16A 的方法：可以通过接口实现HTTP接口远程控制通断、设备电源开关控制、空调电源控制、大功率电器供电、功率计量数据上报、远程定时任务设置、自定义联动操作、按钮动作自定义设置、单路设备电源控制、远程控制电器电源、定时开关电器设备、设备电源状态监测、远程打开关闭电器电源、设备电源通断控制、设备用电定时管控、远程开关状态查询、场景联动电源控制、设备运行状态监控、远程参数配置管理、故障告警通知、过流过载保护控制、延时通断控制、设备分组控制。

智能插座16A

体积小巧，无需走线，标准国标3pin插头；

1位3孔，额定功率3500W；

可接大一匹内空调插头；

按钮动作可自定义、可屏蔽；

功率计量版实时上报计量数据；

HTTP接口远程控制通断；；

支持远程定时任务，支持自定义联动操作；

更多...

适用场景

智能家居设备电源控制、共享自习室空调电源管理、共享棋牌室设备电源控制、共享茶室电器电源管理、共享台球室设备电源控制、共享场所电器电源管理、智能办公设备电源控制、门店设备电源管理、设备机房电源控制、弱电间设备电源管理、无人值守空间设备电源控制、智能化改造、智能办公、居家电器控制、家庭智能改造、酒店客房智能控制、民宿房间设备管理、共享茶室设备控制、共享自习室电器管理、办公室设备电源控制、店铺设备电源管理、智能公寓客房控制、共享棋牌室设备控制、无人值守空间设备管理、弱电间设备联动、智能家居电器控制、出租屋用电安全管理、小型商铺设备电源控制、共享充电设备管理、共享按摩椅电源控制、自助设备电源管理、无人售货机电源控制、自助洗衣设备电源管理、共享健身房设备电源控制、共享台球室设备电源管理、共享麻将馆设备控制、自助洗车设备电源管理、共享充电站设备管理、智慧教室设备电源控制、培训机构设备电源管理、图书馆设备电源控制、创客工坊设备电源管理、学校活动室设备电源控制、培训教室设备电源管理、餐厅设备电源控制、便利店设备电源管理、银行网点设备电源控制、医院设备电源管理、展会现场设备电源控制、活动现场设备电源管理、景观亮化设备电源控制、广告灯箱设备电源管理、园区设备电源控制、写字楼设备电源管理、商场设备电源控制、社区公共设备电源管理中

支持命令

开关	power
先通后断	point
先断后通	reset

产品手册

版本	对应产品手册
不带功率计量	《智能插座16A产品手册》
功率计量版	《智能插座16A[计量版]产品手册》

HTTP接口控制以设备控制（向设备下发命令）为例

<?php

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

$curl = curl_init();

$AppID = '开发者ID'; // 替换为实际的 AppID
$AppSecret = '开发者密码'; // 替换为实际的 AppSecret
$ts = time();
$sign = md5(md5($AppSecret) . $ts); //md5(md5(开发者密码)拼接上面的ts参数)
$url = 'https://api.thingboot.com/{appid}/device/control/?sign={sign}&ts={ts}';
$url = str_replace(
    array('{appid}', '{sign}', '{ts}'),
    array($AppID, $sign, $ts),
    $url
);

// 请求体数据
$device = '1878'; // 替换为实际的设备ID；可传多个[用,间隔]
$order = '{"power1":1}'; // 替换为实际的命令
// 构建请求体
$postData = json_encode([
    'device' => $device,
    'order' => json_decode($order) // 确保命令是有效的 JSON 对象
]);
curl_setopt_array($curl, array(
    CURLOPT_URL => $url,
    CURLOPT_RETURNTRANSFER => true,
    CURLOPT_ENCODING => '',
    CURLOPT_MAXREDIRS => 10,
    CURLOPT_TIMEOUT => 0,
    CURLOPT_FOLLOWLOCATION => true,
    CURLOPT_HTTP_VERSION => CURL_HTTP_VERSION_1_1,
    CURLOPT_POST => true, // 设置为 POST 请求
    CURLOPT_POSTFIELDS => $postData, // 设置请求体
    CURLOPT_HTTPHEADER => array(
        'Content-Type: application/json', // 设置请求头为 JSON 格式
    ),
));
$response = curl_exec($curl);
curl_close($curl);
echo $response;

<?php

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

//确保你已经安装了 HTTP_Request2
require_once 'HTTP/Request2.php';

$AppID = '开发者ID'; // 替换为实际的 AppID
$AppSecret = '开发者密码'; // 替换为实际的 AppSecret
$ts = time();
$sign = md5(md5($AppSecret) . $ts); // 确保签名的计算方式符合 API 文档的要求

$url = 'https://api.thingboot.com/{appid}/device/control/?sign={sign}&ts={ts}';
$url = str_replace(
    array('{appid}', '{sign}', '{ts}'),
    array($AppID, $sign, $ts),
    $url
);

// 请求体数据
$device = '1878'; // 替换为实际的设备ID；可传多个[用,间隔]
$order = '{"power1":1}'; // 替换为实际的命令

// 构建请求体
$postData = json_encode([
    'device' => $device,
    'order' => json_decode($order, true) // 确保命令是有效的 JSON 对象
]);

// 创建 HTTP_Request2 对象
$request = new HTTP_Request2($url, HTTP_Request2::METHOD_POST);
$request->setHeader('Content-Type', 'application/json');
$request->setBody($postData);

// 发送请求并获取响应
try {
    $response = $request->send();
    if ($response->getStatus() == 200) {
      echo $response->getBody();
    }else {
      echo 'Unexpected HTTP status: ' . $response->getStatus() . ' ' .
      $response->getReasonPhrase();
    }
} catch (HTTP_Request2_Exception $e) {
    echo 'Error: ' . $e->getMessage();
}

<?php

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

$AppID = '开发者ID'; // 替换为实际的 AppID
$appSecret = '开发者密码'; // 替换为实际的 AppSecret
$ts = time();
$sign = md5(md5($appSecret) . $ts); // 确保签名的计算方式符合 API 文档的要求
 
$url = 'https://api.thingboot.com/{appid}/device/control/?sign={sign}&ts={ts}';
$url = str_replace(
    array('{appid}', '{sign}', '{ts}'),
    array($AppID, $sign, $ts),
    $url
);

// 请求体数据
$device = '1878'; // 替换为实际的设备ID；可传多个[用,间隔]
$order = '{"power1":1}'; // 替换为实际的命令
 
// 构建请求体
$postData = json_encode([
    'device' => $device,
    'order' => json_decode($order, true) // 确保命令是有效的 JSON 对象
]);
 
// 创建 HttpRequest 对象
$request = new HttpRequest($url, HttpRequest::METH_POST);
$request->setContentType('application/json');
$request->setBody($postData);
 
// 发送请求并获取响应
try {
    $response = $request->send();
    if ($response->getResponseCode() == 200) {
        echo $response->getBody();
    } else {
        echo 'Unexpected HTTP status: ' . $response->getResponseCode() . ' ' .
             $response->getStatusMessage();
    }
} catch (HttpException $e) {
    echo 'Error: ' . $e->getMessage();
}

<?php

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

require 'vendor/autoload.php';
 
use GuzzleHttp\Client;
use GuzzleHttp\Exception\RequestException;

$AppID = '开发者ID'; // 替换为实际的 AppID
$appSecret = '开发者密码'; // 替换为实际的 AppSecret
$ts = time();
$sign = md5(md5($appSecret) . $ts); // 确保签名的计算方式符合 API 文档的要求
 
$url = 'https://api.thingboot.com/{appid}/device/control/?sign={sign}&ts={ts}';
$url = str_replace(
    array('{appid}', '{sign}', '{ts}'),
    array($AppID, $sign, $ts),
    $url
);

// 请求体数据
$device = '1878'; // 替换为实际的设备ID；可传多个[用,间隔]
$order = '{"power1":1}'; // 替换为实际的命令
 
// 构建请求体
$postData = json_encode([
    'device' => $device,
    'order' => json_decode($order, true) // 确保命令是有效的 JSON 对象
]);

// 创建 Guzzle 客户端
$client = new Client();
 
try {
    // 发送 POST 请求
    $response = $client->post($url, [
        'headers' => [
            'Content-Type' => 'application/json',
        ],
        'body' => $postData
    ]);
 
    // 获取响应体内容
    echo $response->getBody();
 
} catch (RequestException $e) {
    // 捕获请求异常
    if ($e->hasResponse()) {
        echo 'Unexpected HTTP status: ' . $e->getResponse()->getStatusCode() . ' ' .
             $e->getResponse()->getReasonPhrase();
    } else {
        echo 'Error: ' . $e->getMessage();
    }
}

说明：{AppID}为您的应用ID（由平台生成），免费注册登录后，可在控制台查看；sign和ts的取值，请参考文档。