如何用PHP语言控制门禁系统控制开关

2026-01-21 发布浏览：774 次

本文介绍了如何用 PHP 对接智能墙壁出门开关的方法：可以通过接口实现按下解锁开门、HTTP接口远程控制通断、远程定时任务设置、自定义联动操作、门禁系统联动控制、配合电磁锁电插锁管理门禁。

智能墙壁出门开关

标准86型底盒，安装简单；

可接任何种类的电磁锁、电插锁；

广泛应用于各种门禁控制、门禁改造；

支持断电开锁｜通电上锁、支持断电上锁｜通电开锁两种模式；

HTTP接口远程控制通断；

支持远程定时任务，支持自定义联动操作；

更多...

适用场景

智能家居门禁控制、共享场所门禁管理、智能办公门禁控制、安防门禁场景、门店门禁改造、会议室门禁控制、舞蹈室门禁管理、设备机房门禁控制、弱电间门禁联动、线下服务场景门禁控制、无人值守门

支持命令

开关	power
先断后通	reset
先通后断	point

产品手册

版本	对应产品手册
白色	《智能墙壁出门开关产品手册》

HTTP接口控制以设备控制（向设备下发命令）为例

<?php

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

$curl = curl_init();

$AppID = '开发者ID'; // 替换为实际的 AppID
$AppSecret = '开发者密码'; // 替换为实际的 AppSecret
$ts = time();
$sign = md5(md5($AppSecret) . $ts); //md5(md5(开发者密码)拼接上面的ts参数)
$url = 'https://api.thingboot.com/{appid}/device/control/?sign={sign}&ts={ts}';
$url = str_replace(
    array('{appid}', '{sign}', '{ts}'),
    array($AppID, $sign, $ts),
    $url
);

// 请求体数据
$device = '1878'; // 替换为实际的设备ID；可传多个[用,间隔]
$order = '{"power1":1}'; // 替换为实际的命令
// 构建请求体
$postData = json_encode([
    'device' => $device,
    'order' => json_decode($order) // 确保命令是有效的 JSON 对象
]);
curl_setopt_array($curl, array(
    CURLOPT_URL => $url,
    CURLOPT_RETURNTRANSFER => true,
    CURLOPT_ENCODING => '',
    CURLOPT_MAXREDIRS => 10,
    CURLOPT_TIMEOUT => 0,
    CURLOPT_FOLLOWLOCATION => true,
    CURLOPT_HTTP_VERSION => CURL_HTTP_VERSION_1_1,
    CURLOPT_POST => true, // 设置为 POST 请求
    CURLOPT_POSTFIELDS => $postData, // 设置请求体
    CURLOPT_HTTPHEADER => array(
        'Content-Type: application/json', // 设置请求头为 JSON 格式
    ),
));
$response = curl_exec($curl);
curl_close($curl);
echo $response;

<?php

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

//确保你已经安装了 HTTP_Request2
require_once 'HTTP/Request2.php';

$AppID = '开发者ID'; // 替换为实际的 AppID
$AppSecret = '开发者密码'; // 替换为实际的 AppSecret
$ts = time();
$sign = md5(md5($AppSecret) . $ts); // 确保签名的计算方式符合 API 文档的要求

$url = 'https://api.thingboot.com/{appid}/device/control/?sign={sign}&ts={ts}';
$url = str_replace(
    array('{appid}', '{sign}', '{ts}'),
    array($AppID, $sign, $ts),
    $url
);

// 请求体数据
$device = '1878'; // 替换为实际的设备ID；可传多个[用,间隔]
$order = '{"power1":1}'; // 替换为实际的命令

// 构建请求体
$postData = json_encode([
    'device' => $device,
    'order' => json_decode($order, true) // 确保命令是有效的 JSON 对象
]);

// 创建 HTTP_Request2 对象
$request = new HTTP_Request2($url, HTTP_Request2::METHOD_POST);
$request->setHeader('Content-Type', 'application/json');
$request->setBody($postData);

// 发送请求并获取响应
try {
    $response = $request->send();
    if ($response->getStatus() == 200) {
      echo $response->getBody();
    }else {
      echo 'Unexpected HTTP status: ' . $response->getStatus() . ' ' .
      $response->getReasonPhrase();
    }
} catch (HTTP_Request2_Exception $e) {
    echo 'Error: ' . $e->getMessage();
}

<?php

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

$AppID = '开发者ID'; // 替换为实际的 AppID
$appSecret = '开发者密码'; // 替换为实际的 AppSecret
$ts = time();
$sign = md5(md5($appSecret) . $ts); // 确保签名的计算方式符合 API 文档的要求
 
$url = 'https://api.thingboot.com/{appid}/device/control/?sign={sign}&ts={ts}';
$url = str_replace(
    array('{appid}', '{sign}', '{ts}'),
    array($AppID, $sign, $ts),
    $url
);

// 请求体数据
$device = '1878'; // 替换为实际的设备ID；可传多个[用,间隔]
$order = '{"power1":1}'; // 替换为实际的命令
 
// 构建请求体
$postData = json_encode([
    'device' => $device,
    'order' => json_decode($order, true) // 确保命令是有效的 JSON 对象
]);
 
// 创建 HttpRequest 对象
$request = new HttpRequest($url, HttpRequest::METH_POST);
$request->setContentType('application/json');
$request->setBody($postData);
 
// 发送请求并获取响应
try {
    $response = $request->send();
    if ($response->getResponseCode() == 200) {
        echo $response->getBody();
    } else {
        echo 'Unexpected HTTP status: ' . $response->getResponseCode() . ' ' .
             $response->getStatusMessage();
    }
} catch (HttpException $e) {
    echo 'Error: ' . $e->getMessage();
}

<?php

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

require 'vendor/autoload.php';
 
use GuzzleHttp\Client;
use GuzzleHttp\Exception\RequestException;

$AppID = '开发者ID'; // 替换为实际的 AppID
$appSecret = '开发者密码'; // 替换为实际的 AppSecret
$ts = time();
$sign = md5(md5($appSecret) . $ts); // 确保签名的计算方式符合 API 文档的要求
 
$url = 'https://api.thingboot.com/{appid}/device/control/?sign={sign}&ts={ts}';
$url = str_replace(
    array('{appid}', '{sign}', '{ts}'),
    array($AppID, $sign, $ts),
    $url
);

// 请求体数据
$device = '1878'; // 替换为实际的设备ID；可传多个[用,间隔]
$order = '{"power1":1}'; // 替换为实际的命令
 
// 构建请求体
$postData = json_encode([
    'device' => $device,
    'order' => json_decode($order, true) // 确保命令是有效的 JSON 对象
]);

// 创建 Guzzle 客户端
$client = new Client();
 
try {
    // 发送 POST 请求
    $response = $client->post($url, [
        'headers' => [
            'Content-Type' => 'application/json',
        ],
        'body' => $postData
    ]);
 
    // 获取响应体内容
    echo $response->getBody();
 
} catch (RequestException $e) {
    // 捕获请求异常
    if ($e->hasResponse()) {
        echo 'Unexpected HTTP status: ' . $e->getResponse()->getStatusCode() . ' ' .
             $e->getResponse()->getReasonPhrase();
    } else {
        echo 'Error: ' . $e->getMessage();
    }
}

说明：{AppID}为您的应用ID（由平台生成），免费注册登录后，可在控制台查看；sign和ts的取值，请参考文档。

如何用PHP语言控制门禁系统控制开关

智能墙壁出门开关

适用场景

支持命令

产品手册

HTTP接口控制以设备控制（向设备下发命令）为例

文章：

如何用PHP语言控制门禁系统控制开关

相关技术文章：

如何用PHP语言对接HTTP接口壁挂人体存在检测设备

怎样用PHP语言控制40A带计量数显智能空开

怎样用PHP语言控制被动红外人体感应器

怎么用PHP语言对接1位5孔远程控制电源插座

如何用PHP语言对接60A大功率计量断路器

Please contact me

智能墙壁出门开关

适用场景

支持命令

产品手册

HTTP接口控制 以设备控制（向设备下发命令）为例

文章：

如何用PHP语言控制门禁系统控制开关

相关技术文章：

如何用PHP语言对接HTTP接口壁挂人体存在检测设备

怎样用PHP语言控制40A带计量数显智能空开

怎样用PHP语言控制被动红外人体感应器

怎么用PHP语言对接1位5孔远程控制电源插座

如何用PHP语言对接60A大功率计量断路器

HTTP接口控制以设备控制（向设备下发命令）为例