如何用Java语言控制永久密码门禁

2022-07-10 发布浏览：205 次

本文介绍了如何用 Java 对接智能密码门禁|按键版的方法：可以通过接口实现HTTP接口远程控制门禁、密码下发与取消、动态密码管理、永久密码管理、高密密码验证、验证结果上报、电磁锁电插锁控制、远程定时任务、自定义联动操作。

智能密码门禁|按键版

12位按压按键，反应灵敏

支持HTTP接口下发密码，取消密码

支持100个动态密码（带有效期）

支持30个永久密码（永久有效，断电不丢失）

支持离线密码验证，验证结果通过HTTP接口上报

支持DC12V的任何电磁锁、电插锁

支持远程定时任务，支持自定义联动操作；

更多...

适用场景

智能家居、共享场所、智能办公、安防门禁场景、共享台球厅门禁控制、共享自习室门禁管理、共享茶室门禁控制、智能公寓门禁管理、无人值守空间门禁控制、办公室门禁系统、店铺门禁管理、设备机房门禁控制、弱电间门禁联动中

支持命令

线路	power
设置密码	pwd
密码列表	list
删除密码	delete
清空密码	clear
先断后通	reset
先通后断	point

产品手册

版本	对应产品手册
黑色	《智能密码门禁[按键]产品手册》

HTTP接口控制以设备控制（向设备下发命令）为例

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

/*首先，确保在你的项目中添加了 unirest 的 Maven 依赖。如果你使用的是 Maven，可以在 pom.xml 中添加以下依赖：
<dependency>
    <groupId>com.konghq</groupId>
    <artifactId>unirest-java</artifactId>
    <version>3.13.10</version>
</dependency>
*/

import com.konghq.unirest.http.HttpResponse;
import com.konghq.unirest.http.Unirest;
import com.konghq.unirest.http.exceptions.UnirestException;
import org.apache.commons.codec.digest.DigestUtils;

public class Main {
    public static void main(String[] args) {
        // 定义变量
        String AppID = "开发者ID"; // 替换为实际的 AppID
        String AppSecret = "开发者密码"; // 替换为实际的 AppSecret
        long ts = System.currentTimeMillis() / 1000; // 获取当前时间戳（秒）

        // 计算签名 md5(md5(开发者密码)拼接上面的ts参数)
        String sign = DigestUtils.md5Hex(DigestUtils.md5Hex(AppSecret) + ts);

        // 构建 URL
        String url = String.format("https://api.thingboot.com/%s/device/control/?sign=%s&ts=%d", AppID, sign, ts);

        // 请求体数据
        String device = "1878"; // 替换为实际的设备ID；可传多个[用,间隔]
        String order = "{\"power1\":1}"; // 替换为实际的命令

        try {
            // 构建请求体
            String postData = String.format("{\"device\":\"%s\",\"order\":%s}", device, order);

            // 发送 POST 请求
            HttpResponse<String> response = Unirest.post(url)
                    .header("Content-Type", "application/json")
                    .body(postData)
                    .asString();

            // 输出响应
            System.out.println(response.getBody());
        } catch (UnirestException e) {
            e.printStackTrace();
        }
    }
}

// First you need to prepare the following values
// 1. AppID (in your console development settings)
// 2. AppSecret (in your console development settings)
// 3. ts (timestamp of the current time, seconds)
// 4. YourSign = md5(md5(AppSecret)ts);(md5 is an encryption method, AppSecret is the AppSecret prepared above, ts is the timestamp prepared above, concatenate the string after the AppSecret after md5 encryption)
// In simple terms, the signature is md5(md5(your developer password)concatenate the above ts timestamp value); ts is the timestamp of the current timestamp; that is, to perform one MD5 on the developer password (AppSecret), then concatenate the timestamp, and then perform one MD5 on the entire concatenated string
// Core request address: api.thingboot.com/AppID/device/control/?sign=YourSign&&ts=ts;
// Request needs to pass two parameters device and order:
// device[string]: unique device ID, can pass multiple [separated by ,], can be viewed in the console, or pulled through the interface
// order[json string]: the command to be issued, for example:
// {"power":1}, usually to connect the circuit of the switch
// {"power3":0}, usually to close the third line of the switch or controller
// {"play:gbk:16":"hello, welcome to visit"}, let the voice speaker report the specified content
// The same type of product, the command is the same, different product types of commands, please view the product manual page of each product
// Note: you must replace the formal AppID and AppSecret with real-time timestamp calculation of the signature, the request must have device device ID and order command

/*
首先，确保在你的项目中添加了 OkHttp 的 Maven 依赖。如果你使用的是 Maven，可以在 pom.xml 中添加以下依赖：
<dependency>
    <groupId>com.squareup.okhttp3</groupId>
    <artifactId>okhttp</artifactId>
    <version>4.9.3</version>
</dependency>
*/

import okhttp3.*;
import org.apache.commons.codec.digest.DigestUtils;

import java.io.IOException;

public class Main {
    public static void main(String[] args) {
        // 定义变量
        String AppID = "开发者ID"; // 替换为实际的 AppID
        String AppSecret = "开发者密码"; // 替换为实际的 AppSecret
        long ts = System.currentTimeMillis() / 1000; // 获取当前时间戳（秒）

        // 计算签名 md5(md5(开发者密码)拼接上面的ts参数)
        String sign = DigestUtils.md5Hex(DigestUtils.md5Hex(AppSecret) + ts);

        // 构建 URL
        String url = String.format("https://api.thingboot.com/%s/device/control/?sign=%s&ts=%d", AppID, sign, ts);

        // 请求体数据
        String device = "1878"; // 替换为实际的设备ID；可传多个[用,间隔]
        String order = "{\"power1\":1}"; // 替换为实际的命令

        // 构建请求体
        String postData = String.format("{\"device\":\"%s\",\"order\":%s}", device, order);

        // 创建 OkHttpClient 实例
        OkHttpClient client = new OkHttpClient();

        // 创建请求体
        MediaType mediaType = MediaType.parse("application/json; charset=utf-8");
        RequestBody body = RequestBody.create(postData, mediaType);

        // 创建请求
        Request request = new Request.Builder()
                .url(url)
                .post(body)
                .addHeader("Content-Type", "application/json")
                .build();

        // 发送请求并处理响应
        try (Response response = client.newCall(request).execute()) {
            if (!response.isSuccessful()) throw new IOException("Unexpected code " + response);

            // 输出响应
            System.out.println(response.body().string());
        } catch (IOException e) {
            e.printStackTrace();
        }
    }
}

说明：{AppID}为您的应用ID（由平台生成），免费注册登录后，可在控制台查看；sign和ts的取值，请参考文档。

如何用Java语言控制永久密码门禁

智能密码门禁|按键版

适用场景

支持命令

产品手册

HTTP接口控制以设备控制（向设备下发命令）为例

文章：

如何用Java语言控制永久密码门禁

相关技术文章：

怎么用Java语言对接空调远程指令发送器2

如何用Java语言对接24 路智能分体远程多通道控制器

如何用Java语言控制20W 物联网语音广播音箱

怎样用Java语言控制智能Mini语音喇叭

怎样用Java语言对接10W壁挂语音通知音箱

Please contact me

智能密码门禁|按键版

适用场景

支持命令

产品手册

HTTP接口控制 以设备控制（向设备下发命令）为例

文章：

如何用Java语言控制永久密码门禁

相关技术文章：

怎么用Java语言对接空调远程指令发送器2

如何用Java语言对接24 路智能分体远程多通道控制器

如何用Java语言控制20W 物联网语音广播音箱

怎样用Java语言控制智能Mini语音喇叭

怎样用Java语言对接10W壁挂语音通知音箱

HTTP接口控制以设备控制（向设备下发命令）为例